CAT5 wiring

If this isn't exactly what you wanted, please try our Search (there's a LOT of techy and non-techy stuff here about Linux, Unix, Mac OS X and just computers in general!):

From - Thu Jul 22 18:01:59 1999
Xref: world comp.unix.sco.misc:101557
Path: world!blanket.mitre.org!newsfeed.berkeley.edu!intgwpad.nntp.telstra.net!news2.c2.telstra-mm.net.au!not-for-mail
From: "Vania Lolham" <vlolham@nsw.bigpond.net.au>
Newsgroups: comp.unix.sco.misc
Subject: Re: Hubs
Date: Fri, 23 Jul 1999 01:32:19 +1000
Organization: Telstra Big Pond Cable - Sydney Site 1
Lines: 134
Message-ID: <7n7dbt$eg5$1@m2.c2.telstra-mm.net.au> 
References: <01bed2cc$1ed21b80$0101a8c0@transova> 
Reply-To: "Vania Lolham" <vlolham@nsw.bigpond.net.au>
NNTP-Posting-Host: 24.192.45.12
X-Trace: m2.c2.telstra-mm.net.au 932657341 14853 24.192.45.12 (22 Jul 1999 15:29:01 GMT)
X-Complaints-To: news@m2.c2.telstra-mm.net.au
NNTP-Posting-Date: 22 Jul 1999 15:29:01 GMT
X-Priority: 3
X-MSMail-Priority: Normal
X-Newsreader: Microsoft Outlook Express 5.00.2014.211
X-MimeOLE: Produced By Microsoft MimeOLE V5.00.2014.211
X-Mozilla-Status: 8011

Hi,

You are right about the twist difference in all 4 pairs.
I was called out to many sites big or small from 5 user to 500 use with the
problems most of you facing now!
Example: you or your client started with co-ax cable BNC connector 4 to 10
Mbps depend on who done the cabling and quality of the NIC's and it was fine then.
and as your business grow, your cable length grows too, till
you reach your 185meter limit and accordingly
more traffic in the cable and resulting in a lot of data
collision, packet loss and holts.
you or your client will take the plunge and change to
10base-T, using patch panels and hubs.
at this point the cable guy is the key to achieve the best
performance or a nightmare.
most cable guys didn't know anything about category 1,2,3,4,5
now 6. and run the cables from one side
of the office to the other and over the power cables and
light fittings and bend and twist and squeeze the cable.
end result was okay, the improvement over Co-Ax was 50%
better, and everyone was happy.
until the client decided to go super highway with 100Mbps and
intelligent Auto Sense hubs.
this is where someone will get fired. the bloody hub turned
in to a Christmas tree!, signals keep jumping
up and down flashing from 10 to 100 and data collision light
flashing and so on.
WHY? the answer is not knowing how to design a bullet proof
network from the start to allow growth.
A good practice is to spend a bit more from the start on the
quality of the network cabling and
accessories than finding yourself in a situation that you
have to Re-Do-It all over again.

 Now this is my advise to you.
-------------------------------
Cat-5 Cabling terminology : each pair has a full colour wire twisted with
another of the same colour with stripe or just
white called "mate".(instead of saying "white" or "white with colour X
stripe).
four twisted pairs are: Green-Orange-Blue-Brown
Wiring spec for T568A: pinout:(hold the plug in front of you and clip
pointing up left to write is 1 to 8)
    1-Green(Mate)
    2-Green
    3-Orange(Mate)
    4-Blue
    5-Blue(Mate)
    6-Orange
    7-Brown(Mate)
    8-Brown

Wiring spec for T568B: pinout:
    1-Orange(Mate)
    2-Orange
    3-Green(Mate)
    4-Blue
    5-Blue(Mate)
    6-Green
    7-Brown(Mate)
    8-Brown

Important Note: To achieve 100Mbps (100Mhz) you must follow these
instruction carefully.
    1- Not all Cat-5 cables are suitable for 100Mbps (choose the known
brand), but any Cat-5 will be adequate for 10Mbps.
    2- Cat-5 cable for 100Mbps or 100Mhz freq have to have IEEE standard and
FDDI networks compliant and
         each copper wire have to be 22AWG for Cat-5 and 24AWG for Cat-6,
read the compliance on the
         package or the cable's jacket.
    3- The maximum bending radius of the cable is 25.4mm without the
insulation cracking.
    4- UTP Cat-5 cable shall not cross any power cable carrying more than
60volts, minimum separation 60cm
         between the Data cable and Power cable of  low voltage.
    5- If you are making your own patch cables or terminating your patch
panel have to follow this important method:
                        1-When patching the cable, jacket should not exposed
the wire more than 6mm after termination.
                        2-When terminate each pair, do not UN-twist them
more then 4mm. major losses occurs at the
                            patch panel and workstation's
socket(wall-mount).
                        3- patch cable have to match your patch panel
sockets(read on the socket T568A or T568B)
                            and entire network have to have one type of
wiring implementation.
    6- Never run the cable near fluoro light ceiling unit ( Electro Magnetic
Interference will cause packet loss).
    7- Maximum cable length(segment) from Patch panel to workstation's NIC
is 100 meter no more(best is stay under
         90 meter from the patch panel  to the wall socket then allow 2 to 3
meter for the patch cable from wall socket to
          the NIC.
    8- use a path for all the cables going from patch panel and group them
when they have to change direction.
          follow the nature simple examples: Tree and Heart.
    9- Always use solid wire for cable run from the patch panel to the
workstation and stranded wire for the patch cable
         form patch panel to the hub and from wall socket to the computer.
    --------------
    In most cases for higher velocity and frequency stability use T568A
topology.
    But the most important of all after you did the above is matching your
Hub with the NICs, try to use one manufacturer
    or brand name for your Hubs and NICs for the right speed. Never mix and
match then.

    I hope this short course will solve most of your common problems.

    Regards
    Vania

Kyle Schuiteman <kyles@transova.com> wrote in message
news:01bed2cc$1ed21b80$0101a8c0@transova...
> Hi I have a openserver machine here with a 3com etherlink xl card in it.
>
> Here is the probelm.  I put in a new 3com superstack entry hub to replace
> an older 3com linkbuilder hub.  The server will be seen on the old hub but
> not on the new one.( I can ping the server on the old one and not on the
> new one).  What gets stranger is if I link the old hub to the new one and
> plug the server into the old hub that works too.
> I have a test machine here with same software setup etc and it connects
> just fine to the new hub.  Any ideas.  It has to be a setup issue with the
> network card.
>
> please respond vi email
> kyles@transova.com

Versatile Site Map Generator $59.00
A1 Sitemap Generator

Jump to Comments

Many of the products and books I review are things I purchased for my own use. Some were given to me specifically for the purpose of reviewing them. I resell or can earn commissions from the sale of some of these items. Links within these pages may be affiliate links that pay me for referring you to them. That's mostly insignificant amounts of money; whenever it is not I have made my relationship plain. I also may own stock in companies mentioned here. If you have any question, please do feel free to contact me.

Specific links that take you to pages that allow you to purchase the item I reviewed are very likely to pay me a commission. Many of the books I review were given to me by the publishers specifically for the purpose of writing a review. These gifts and referral fees do not affect my opinions; I often give bad reviews anyway.

We use Google third-party advertising companies to serve ads when you visit our website. These companies may use information (not including your name, address, email address, or telephone number) about your visits to this and other websites in order to provide advertisements about goods and services of interest to you. If you would like more information about this practice and to know your choices about not having this information used by these companies, click here.